How long does Pebble Tec have to cure?

Pebble Tec Explained

The very top layer of cement is then hosed away to expose the pebbles, and the pool is left to cure for about 24 hours. After that, the surface is acid rinsed and treated to bring out the pebbles' brightness.

How soon can you swim in a new pool with PebbleTec?

They usually do an Acid startup on Pebble finishes which takes about 7 days. Thats tough...they usually don't want you swimming in it for the first week. Also, don't know how large your pool is, but it could take 2 days or more to fill the pool up you know.

Why do you brush PebbleTec?

Brushing a Pebble Tec surface is also very important, especially during the first few weeks after application, but also afterwards, to keep dirt and algae from building up on the slightly irregular surface. Be sure to use only a nylon pool brush, never use a steel bristled pool brush on a Pebble Tec surface.

Can you PebbleTec a pool in the rain?

Rain, no problem. actually it helps with the cure if it doesn't happen until the cement is set. they will pump it out and do the acid wash and it will be fine.

Do you need to brush New PebbleTec?

The start-up process is not hard to perform but does require frequent water testing, brushing and chemical balancing. It is important to note that the start-up will have the most influence on the final appearance and longevity of your interior finish.

The Benefits of PebbleTec

When can I heat my pool after pebble Tec?

Pebble Tec says DO wait at least 14 days before heating the water and monitor chemical balance more closely after you turn on your heater. Other places say to not run the heater until there is no more plaster dust when brushing the walls. Its your pool to do as you wish.

When can I fill my pool after pebble Tec?

Like all cement based interior pool finishes, all of the Pebble Plus products are water cured. This means they must be filled with water as soon as possible after installation.

Can you leave a Pebble Tec pool empty?

Does my pool need to be drained before cleaning pool tile or cleaning pebble-tec? No! - We lower your pool water just enough to expose all the pool tile calcium and pebble-tec calcium. In an effort to conserve water, We Never Need to Drain Your Pool.

How often should you acid wash a Pebble Tec pool?

If you regularly clean your pool and keep it in good shape, chances are you will only need to acid wash your swimming pool every 5-7 years. Because acid washing uses harsh chemicals, it is not recommended to get your pool acid washed more frequently than that, as the harsh chemical used can damage your pool's surface.

What does acid wash do for Pebble Tec?

Pebble Tec Pools

An Acid wash consists of a mixture of water and muriatic acid. The acid makes contact with the pools surface and gently removes a small layer, revealing a fresh layer of plaster underneath. This type of cleaning is intense and best-suited for removing tough surface stains from plaster and Pebble Tec.

Can Pebble Tec be exposed to sun?

The stone material is less impervious to attack or alterations in appearance due to lack of proper pool maintenance. The aggregate can be exposed to the sun without damage to the surface in most cases. The exposed aggregate can be rough on some people's skin making it less appealing than the smoother plaster finish.

Does Pebble Tec hurt your feet?

Cons of Pebble Pool Surfaces

Pebble pool finishes are generally pricier than plaster finishing, and it is true that pebble pool surfaces can be a bit rough on feet if not installed correctly. Calcium or mineral buildup can also be a concern for pebble pool surfaces.

What is better than Pebble Tec?

River rok is good alternative, stones are somewhat smaller and smoother than pebble tec. Can also custom the colors to your liking.

Can you use pumice stone on Pebble Tec?

Yes you can. However we don't recommend using pumice stones. Cleaning with a pumice stone takes a lot of time and effort. Depending on the amount of calcium build up this could take hours and hours over several weekends.

Which is better Pebble Tec vs wet edge?

Unlike Wet Edge, Pebble Tec utilizes superior material that is able to enhance the look and feel of backyards with naturally tumbled stones and the finest pebbles from all across the world.

Can you pressure wash Pebble Tec?

As with any pool, a Pebble Tec pool needs to be drained before you clean it. Once drained, take the opportunity to survey it carefully for loose pebbles or cracked spots. You'll be pressure washing the Pebble Tec pool on very low pressure, so you'll need to use soap to loosen up the dirt before you start.

Will a pool pop out of the ground?

Much of this rain water penetrates into the ground, raising the inground water table, which creates a lot of hydrostatic pressure pushing up on the pool. After the water table raises enough, the pool may float or pop up out of the ground.

How long does pebble plaster take to dry?

DO. allow time (approx. 28 days) before assessing your final water and finish colors. The start-up and balance will allow the water and finish color to change over this period.

How soon can you swim after plastering pool?

The plaster material cures under water in about 7-10 days. But this doesn't mean you have to wait that long. Once the pool is filled and clean, you can go in for a swim.

How long after plaster can you heat pool?

Do NOT use a pool heater until all plaster dust has been removed from the pool. This can typically be accomplished between day 4 and day 10. Do NOT use these devices until AFTER the 28 days startup is complete.

How long does pebble pool finish last?

How Long Will Pebble Tec Last? Traditional pool resurfacing materials require a high level of maintenance and will only last 5-10 years before it needs to be replaced. We generally would expect a Pebble Tec surface to last upwards of 20 years with proper maintenance.

Is PebbleTec a gunite?

Pebble Tec is a mix of large pebbles, stone aggregate, and cement. This is the most durable of the plaster pool types as its surface last from 15 to 20 years +. Pebble Tec is the top choice for gunite pool buyers.

What happens after Pebble Tec?

After a hardening period, your PebbleTec pool finish will be pressure washed and detailed using a special acid solution to remove any residue or film. For certain finishes, the surface is also lightly buffed during the cleansing treatment to polish the stones. These treatments enhance the natural beauty of the finish.

Is PebbleTec really worth it?

Overall. Pebble Tec pools are works of stunning beauty that can last for decades. They are an excellent choice for any pool. Once established, they're easy to maintain.